產品展示
PRODUCT
PE hose
PE軟管采用聚乙烯材料制作而成，與PE硬管相比，管壁較薄，連接使用方便。成本造價較低，經濟實用，現已被廣泛的應用于農業灌溉。 PE hose is made of PE material. Compared with PE rigid pipe, the PE hose has a thin wall and can be connected and used conveniently. The cost of the product is low. It has been widely applied in agricultural irrigation. 產品型號參數：Φ50（壁厚0.8mm）、Φ63（壁厚0.6/0.8/1.2mm）、Φ75（壁厚1.2mm、1.3mm）、Φ90（壁厚1.2mm/1.6mm）。 Product models/ parameters: Φ50 (wall thickness 0.8mm), Φ63 (wall thickness 0.6/0.8/1.2mm), Φ75 (wall thickness 1.2mm, 1.3mm), Φ90 (wall thickness 1.2mm/1.6mm) . 產品特點： Product features: ①成本造價低，PE軟管成本只有硬管的一半左右。 ②使用回收方便，柔韌性強，便于回收，且使用壽命長，性價比高。 ③配套管件齊全，安裝使用方便快捷。 PE軟管除了在微噴帶連接中使用外，也可以用于滴灌帶的連接，在大田微滴灌上應用極為廣泛。 ① The product's cost is low. The cost of PE hose is only about one half of that of hard pipe. ② The product can be used and recycled conveniently. It is featured with strong flexibility, convenient recycling, long service life and high cost performance. ③ We provide a complete range of auxiliary pipe fittings, guaranteeing convenient and fast installation and use. Except for use in connection of micro sprinkling hoses, PE hose can also be used for connection of drip irrigation hoses, so it is applied in field micro drip irrigation very widely.
PE pipe
PE管是一款采用聚乙烯樹脂為原材料，添加必要的輔助配料，經擠出加工而成的一種產品。 PE pipe is a product made of polyester resin and necessary auxiliary materials through extrusion processing. 產品型號：常用的PE管型號主要包括Φ16、Φ20、Φ25、Φ32、Φ40、Φ50、Φ63、Φ75、Φ90、Φ110等（一般管徑較小的PE管為盤管）。根據管徑及壁厚不同（壁厚1.0mm-7.0mm），其承壓范圍從0.32MPa-1.6MPa不等。產品特點：（PE管常用型號Φ16*1.0；Φ16*1.2；Φ20*1.5；Φ25*1.8；Φ32*2.0；Φ40*2.3；Φ50*3.0；Φ63*3.0；Φ63*3.5） Model: Commonly used PE pipe models mainly include Φ16, Φ20, Φ25, Φ32, Φ40, Φ50, Φ63, Φ75, Φ90, Φ110 and so on (usually PE pipe with a small pipe diameter is coil). According to the pipe diameter and the wall thickness (1.0mm-7.0mm), its pressure bearing scope ranges from 0.32MPa-1.6MPa. Product features: (commonly used PE pipe models Φ16*1.0; Φ16*1.2; Φ20*1.5; Φ25*1.8; Φ32*2.0; Φ40*2.3; Φ50*3.0; Φ63*3.0; Φ63*3.5) ①產品連接方便、施工簡單，各種型號的鎖緊管件齊全。PE管在安裝完成后即可試水，使用方便； ②PE管具有良好的剛性、強度，也有很好的柔性；韌性、撓性好，斷裂伸長率高，在不均勻沉降地區使用時效果極佳。 ③耐腐蝕、無需防腐處理，耐磨性能強，PE管正常使用壽命可達50年以上。 ④產品內壁光滑，流通能力大，水流阻力小，輸水能力強，且產品成本低，性價比高。 ⑤低溫抗沖擊性好，聚乙烯的低溫脆化溫度極低，可在-20~40℃溫度范圍內安全使用。材料抗沖擊性好，便于冬季安全使用，不會發生管子脆裂。 ① The product can be connected conveniently. Construction is simple. We provide a complete series of locking pipe fittings. After installation of PE pipe, water testing can be carried out. It is convenient to use. ②PE pipe is of good rigidity, strength, tenacity and flexibility as well as elongation at break. It can achieve superb effects in areas with uneven sedimentation. ③ The product is anti-corrosion and high abrasive resistance, separate anti-corrosion treatment is not needed. Thus the normal service life of PE pipe can be up to over 50 years. ④ The inner wall of the product is smooth, the flow capacity is large, the water flow resistance is small, the water delivery capacity is strong, the product cost is low, and the cost performance is high. ⑤ The product has good impact resistance performance at a low temperature. The low-temperature brittle point temperature of PE is extremely low. It can be used safely within -20~40℃. With good impact resistance performance, the product can be used safely in winter without brittle rupture of pipes. 產品應用范圍：PE管目前廣泛的應用于農業灌溉、城鎮給排水、園林綠化管網等。 Application range of the product: PE pipe has been widely applied in agricultural irrigation, urban water supply and drainage, gardening pipeline, etc.
Fully-automatic fertilizer applicator
智能水肥一體機 三吸肥ZNC Intelligent water-fertilizer AIO three fertilizer sucking channels ZNC 智能施肥機YN-ZNF 1. 三通道施肥，通道單路250L/H 1.5KW stainless steel fertilization pump Manual partitioning 7 inch touch screen control Fertilizer sucking quantity adjusted manually 6. 三路肥料自動攪拌功能 7.肥料瞬時流量和累計流量顯示 stantaneousnd accumulated flow display of fertilizer 三通道施肥，通道單路250L/H 2. 1.5KW不銹鋼工業注肥泵 Rated fertilization pressure 8kg. 4. 注肥流量1.2方\H 3 Solenoid valve extension control function in the external area (256 channels extensible) 7. 自動混肥攪拌功能 Irrigation fertilization process extension 9. 水源水泵首部控制 10. 灌溉模式：分區循環、定時定量控制 Area-based circulation, timing and quantitative control. 11. 可以實時監測注肥總量和瞬時注肥量、實時監測工作電壓 , 各類故障實時監測和報警功能. 可擴展氣象站、土壤墑情、物聯網平臺等 可選配置Optional configuration 手機APP (包含三年服務費 ) 云平臺連接手機端PC端Mobile APP (including three years of service fee), cloud platform connecting the mobile end and the PC end 自動混肥攪拌桶含攪拌電機+304不銹鋼攪拌桿（化工級）500LAutomatic fertilizer mixing barrel, including mixing motor + 304 stainless steel mixing rod (chemical class) 500L
Adjustable red dripper
紅色可調式滴頭由兩部分組成，上半部分是一個紅色帶有8孔出水口的旋轉帽，下半部分是一個黑色帶有外絲的承插接口。 The adjustable red dripper is composed of two parts. The upper part is a red turncap with eight water outlets. The lower part is a black socket (bell) and spigot joint with outer threads. 紅色的旋轉帽上有標注流量調節大小的方向，順時針方向為調小出水流量的方向，逆時針方向是調大出水流量的方向。正常工作時噴灑半徑：0-0.4m ；水量：0-70L每小時。 The red turncap carries a mark showing the flow size adjustment direction. The water flow will decrease by turning the turncap clockwise and will increase by turning it counterclockwise. The sprinkling radius during normal operation: 0-0.4m; Water yield: 0-70L per hour.
公司優勢
Why choose us
Water, fertilizer and labor saving
Drip irrigation belongs to whole pipeline water delivery and local micro irrigation, which reduces water leakage and loss. The drip irrigation system is only controlled manually or automatically through the valve and combined with fertilization, so it can save labor input and reduce production cost.
Control temperature and humidity
Drip irrigation belongs to local micro irrigation. Most of the soil surface remains dry, and the dripper evenly and slowly supplies water to the root soil layer, which can maintain and recover the ground temperature, reduce water evaporation and reduce indoor humidity.
Maintain soil structure
Drip irrigation belongs to micro irrigation. Water infiltrates into the soil slowly and evenly, which can maintain the soil structure.
Improve quality, increase production and income
Because the application of drip irrigation reduces the application amount of water and fertilizer, pesticides and the occurrence of diseases and pests, it can improve the quality of products and advance the time to market.
Perfect design and construction
Provide professional and perfect construction scheme and provide all-round one-stop service.
Hebei Runtian water-saving equipment Co., Ltd. located in Shijiazhuang, the capital of Hebei Province, provides customers with a series of complete sets of products and equipment such as drip irrigation system, drip irrigation belt and micro drip irrigation. At the same time, it can also provide design planning, budget preparation, production and supply of irrigation products, construction and installation of water-saving irrigation projects.
新聞中心
NEWS
2022-01
Installation of shed drip irrigation system
When drip irrigation is carried out in the shed, water outlets are generally set inside each shed. Devices such as filtration and fertilization can be connected from the water outlet. The following describes the connection of pipe fittings and equipment in detail. According to the area of greenhouse, reasonably divide the wheel irrigation group. Select a pipe with economic and reasonable pipe diameter on the basis of meeting irrigation water demand as the main pipe. First, install the head of the whole drip irrigation system. After the pipe (PE pipe) at one end of the water outlet, use a PE outer wire to lock and directly connect a PVC inner wire ball valve of the corresponding model. Because the PVC inner wire ball valve and Venturi fertilizer applicator are inner wire fittings, one iron pair of wires can be used to connect them. In order to ensure the tightness of the connection, an appropriate amount of raw material belt needs to be wound during the connection. The other side of the venturi fertilizer applicator is screwed and connected with the mesh filter (laminated filter) of the outer wire. Finally, the mesh (laminated) filter of the outer wire is locked and connected with the PE pipe through a PE inner wire locking straight through, and a complete set of head is installed. After the water transmission pipeline is connected from the head, the pipeline shall be arranged according to the irrigation zoning. In the greenhouse, PE pipe (or PVC pipe) can be selected as the water transmission pipeline. Generally, there is no trenching in the shed, and the pipeline is laid on the ground. The branch pipe generally adopts PE pipe or soft belt (convenient for drilling and connecting drip irrigation belt / pipe). The last is the installation of end emitters, commonly used as drip irrigation belt or drip irrigation pipe. For the shed with PE pipe as branch pipe and drip irrigation belt for drip irrigation, the corresponding model of punch shall be used first（ Φ 16) Punch holes in the PE pipe, then install the upper pull ring bypass or reverse bus (positive bus) bypass, and then connect the drip irrigation belt with the bypass. Pipe fittings with valves can also be used, which is more convenient to control during use. The end of the drip irrigation belt can be connected with a pull ring plug, or a section of the drip irrigation belt can be cut. The end of the drip irrigation belt can be folded several times and stuffed into the cut drip irrigation belt, which makes the connection more convenient. 在大棚內的做滴灌時，一般每個大棚內部設有出水口。過濾施肥等裝置便可從出水口進行連接。下面詳細介紹一下管件器材連接情況。 根據大棚面積，合理的劃分輪灌組。選擇一種在能滿足灌溉需水量的基礎上，比較經濟合理的管徑的管材作為主管。 首先安裝整套滴灌系統的首部，從出水口一端管（PE管）后，先使用一個PE外絲鎖緊直通連接一個對應型號的PVC內絲球閥，因PVC內絲球閥與文丘里施肥器均為內絲管件，故可采用一鐵對絲將其進行連接。為了保證連接的密封性，連接時需要纏繞適量的生料帶。文丘里施肥器另一側與外絲的網式過濾器（疊片式過濾器）進行擰緊連接。最后將外絲的網式（疊片式）過濾器通過一個PE內絲鎖緊直通與PE管鎖緊連接，一套完整的首部便完成了安裝。 輸水管道從首部連接出后，根據灌溉分區布置管道，大棚溫室內，輸水管可選用PE管（或PVC管均可），一般棚內不進行挖溝，管道鋪設于地面。支管一般采用PE管或軟帶（便于打孔連接滴灌帶/管）。 最后是末端灌水器的安裝，常用的為滴灌帶或滴灌管。對于采用PE管為支管、采用滴灌帶進行滴灌的大棚，連接時先用相應型號的打孔器（Φ16）在PE管上打孔，然后安裝上拉環旁通或反母（正母）旁通，然后將滴灌帶與旁通連接，也可以采用帶有閥門的管件，使用時更便于控制。滴灌帶末端可以用拉環堵頭連接，也可以剪斷一段滴灌帶，將滴灌帶末端折疊幾次后塞入剪斷的滴灌帶中，連接更為便捷。2022-01
Composition and installation mode of dropping arrow system
Drip arrows are often used for potted crops, and also for crops with frequent or uneven planting spacing (such as flowers). The pipeline layout is consistent with other irrigation systems, and the planting quantity and direction of crops need to be considered, so as to reasonably arrange the direction of main and branch pipes. The common dropping arrow system is mainly composed of water source, head hub (often equipped with water pump, check valve, gate valve, pressure gauge, flow meter, etc.), transmission and distribution water pipe network and end emitter dropping arrow, etc. Drip arrow belongs to a precision irrigation technology, which has high requirements on the water quality of the water source. It is generally necessary to install filters of suitable models when in use. The common ones are mainly centrifugal filters and mesh filters. If relatively clean groundwater is used, a filter with a small mesh number can be installed or no filter can be installed. For irrigation with river water, reservoir water or storage pool water, filters must be installed. At the same time, the combination of centrifugal filter and online filter is better. Combination and connection of dropping arrows: the common combination methods of dropping arrows are single arrow, one out two or one out four dropping arrows. Users can also choose long arrow, short arrow, straight arrow and curved arrow according to actual needs. A small tee or a small five-way is used as a connector in use Φ 3 capillary connection. In general, we use the dropping arrow in combination with the pressure compensated dripper to ensure double guarantee, so that the water from the dropping arrow is more stable and uniform. In this way, Φ 3. The capillary is connected with the pressure compensated emitter, and then Φ 3 punch holes on the capillary (commonly used) Φ 20 or Φ 16pe pipe), connect the pressure compensated emitter with the capillary orifice. Finally, insert the dropping arrow into the soil and fix it. After the annual irrigation, collect the dropping arrows, clean them and keep them properly for use when the next irrigation season comes. 滴箭常用于盆栽作物使用，也適用于作物種植間距經常改變或不均勻的作物（如花卉）。管道布置和其他灌溉系統一致，需要考慮作物種植數量、走向，從而合理的布置干、支管走向。 常見的滴箭系統主要有水源、首部樞紐（常配有水泵、逆止閥、閘閥、壓力表、流量表等）、輸配水管網及末端灌水器滴箭等幾部分組成。 滴箭屬于一種精度灌溉技術，對水源水質要求較高，使用時一般需要安裝適應型號的過濾器，常見的主要有離心過濾器、網式過濾器。如采用較為潔凈的地下水，可以安裝目數較小的過濾器或不安裝過濾器。對于采用河水、水庫水或蓄水池水進行灌溉時，必須安裝過濾器。同時采用離心式過濾器及網上過濾器組合效果更佳。 滴箭的組合連接：滴箭常用的組合方式有單箭、一出二式或一出四式滴箭。用戶也可以根據實際需求選擇長箭、短箭、直箭及彎箭。使用中采用小三通或小五通作為連接件，與Φ3毛管連接。通常使用時，我們采用滴箭與壓力補償式滴頭配合使用，雙重保障，這樣滴箭出水更加穩定、均勻。采用此種方式時，Φ3毛管與壓力補償式滴頭連接，然后采用Φ3打孔器在毛管上打孔（常用Φ20或Φ16PE管），將壓力補償式滴頭與毛管孔口連接。最后，將滴箭箭頭插入土中固定即可。待每年灌溉結束后，將滴箭收好，清洗干凈后妥善保存，待下次灌溉季節來臨時使用。2022-01
Eight misunderstandings in the use of drip irrigation systems. I don't know that these drip irr
Error 1: unreasonable irrigation system, drip irrigation flow is low, and users often can't see the irrigation process. If the irrigation time is too long, there will be deep leakage waste; If the irrigation time is too short, the root system will suffer from water stress. Understanding the irrigation intensity, plant water demand and soil field capacity of the irrigation system can better irrigate according to the needs of plants. At the same time, it should be borne in mind that the irrigation period and amount should be adjusted according to the climate and different growth stages of plants, and the same irrigation system cannot always be used. Error 2: the wrong dripper is adopted. The dripper is usually divided into two types: pressure compensated dripper and non pressure compensated dripper. Pressure compensation is more expensive, but the effect is better. First of all, the pressure compensation dripper can ensure that the water output of each dripper is uniform and the fertilization and irrigation are uniform. Secondly, some pressure compensated drippers can wash out the sundries blocking the dripper, and some pressure compensated drippers have large flow channels, which reduces the possibility of dripper blocking. Error 3: lack of filtration equipment. Many users mistakenly believe that well water does not need filtration. In fact, well water often contains coarse sand, fine sand and some chemicals to block the dripper. Common filters include screen filter, laminated filter and sand filter. If there is sand in the water, centrifugal filter should be used. Before installing the filtration system, analyze the physical and chemical composition of the water quality, adopt appropriate filtration facilities according to the water quality, and select the dripper with anti blocking performance. Error 4: there is no fertilization through the drip irrigation system. The simultaneous application of water and fertilizer is the biggest advantage of drip irrigation. The growth of plant roots is water and fertilizer oriented, and the application efficiency of fertilizer with irrigation water is the highest. However, when using the fertilization and irrigation system, there should be a device to prevent fertilizer backirrigation, so as to prevent fertilizer from polluting groundwater and other water sources. Error 5: lack of routine maintenance drip irrigation system needs careful maintenance to achieve optimal performance. Units with conditions shall often flush drip irrigation pipes to ensure smooth water flow of equipment. According to actual needs, periodic combined use of effective chemical treatment can be considered. Error 6: without pressure gauge and flow meter, these simple devices can help users "feel the pulse" of the irrigation system, so as to solve the problem of drip irrigation system that can not be accurately judged by the naked eye. Use a pressure gauge to detect the pressure at the head, middle and tail of the drip irrigation capillary, and compare the historical situation of the design pressure or water pressure to judge the problems of the drip irrigation system. The flowmeter can help users quickly judge the flow of water source. In addition, the flow data is helpful to calculate the actual flow and the historical flow of irrigation system. Error 7: mistakenly believe that all pipes are of the same quality. Different drip irrigation pipes have different raw material quality, production process and patented technology. More importantly, the dripper structure design of different brands of pipes is different. Drip irrigation pipes that can provide uniform water and fertilizer, have anti blocking performance, long service life and are easy to install and maintain should be selected. Error 8: ignoring the long-term operation cost, the drip irrigation system often needs to be used for more than ten or 20 years to irrigate millions of cubic meters of water and fertilizer, so it is very important to consider the uniformity of irrigation, the operation cost of pump station and daily maintenance cost. A well-designed system in the early stage can reduce the later operation cost through its good uniformity or energy saving. In addition, some suppliers have a lot of experience and know-how, which can guide users to select the correct irrigation system and provide help in the operation and maintenance of the system. 錯誤1：不合理的灌溉制度 滴灌流量低，使用者常常會看不到灌水過程，如果灌溉時間太長，則有會產生深層滲漏浪費；如果灌溉時間太短，根系又將發生水分脅迫。了解灌溉系統的灌水強度、植物需水量和土壤田間持水量，就能更好地根據植物需要進行灌溉。同時要銘記，灌溉周期和灌溉量要根據氣候和植物的不同生長階段而調整，不能始終采用同一灌溉制度。 錯誤2：采用錯誤的滴頭 滴頭通常分為兩種型號，壓力補償式滴頭和非壓力補償式。壓力補償式雖然貴一些，但效果更好。首先，壓力補償滴頭可確保每一個滴頭出水均勻，施肥灌溉均一。其次，部分壓力補償式滴頭可將堵塞滴頭的雜物洗出，還有一些壓力補償式滴頭流道很大，減少了滴頭堵塞的可能性。 錯誤3：缺少過濾設備 許多使用者錯誤的認為井水不需要過濾，而事實上井水經常含有粗砂、細砂和一些化學物質，堵塞滴頭。常見的過濾器有網式過濾器、疊片過濾器和砂石過濾器，如果水中有砂則宜采用離心過濾器。在開始安裝過濾系統前，要對水質的物理和化學組成進行分析，根據水質采用合適的過濾設施，并且選擇具有抗堵塞性能的滴頭。 錯誤4：沒有通過滴灌系統進行施肥 水肥同步施入是滴灌的最大優點。植物根系生長具有向水、向肥性，肥料隨灌溉水施用效率最高。但使用施肥灌溉系統要有防止肥料倒灌裝置，以防肥料污染地下水和其他水源。 錯誤5：缺乏日常維護 滴灌系統需要通過精心維護以發揮最優性能。有條件的單位應經常沖洗滴灌管，保證設備水流的暢通。根據實際需要，可以考慮周期性配合使用有效的化學處理。 錯誤6：沒有壓力表和流量表 這些簡單的設備可以幫助使用者給灌溉系統“把脈”，以解決憑肉眼無法準確判斷的滴灌系統問題。用壓力表檢測滴灌管首部、中部和滴灌毛管尾部的壓力情況，對比設計壓力或水壓的歷史情況，可以判斷滴灌系統的問題。流量計可以幫助使用者快速判斷水源的流量，另外，流量數據有助于計算實際流量和灌溉系統的歷史流量情況。 錯誤7：誤認為所有的管品質一樣 不同的滴灌管有不同的原材料品質、生產工藝和專利技術，更重要的是不同品牌管子的滴頭結構設計是不同的。應該選擇可以提供均勻水肥，具備抗阻塞性能，壽命長，易于安裝和維護的滴灌管。 錯誤8：忽視長期運行費用 滴灌系統往往要使用十幾年或20年以上，灌溉數百萬立方的水肥，所以考慮灌溉的均勻度、泵站的運行費用以及日常維護費用非常重要。一個前期設計良好的系統，可通過其良好的均勻度或節能性降低后期運行成本。另外，一些供應商有很多經驗和專有技術，可以指導使用者選用正確的灌溉系統，并在運行和維護系統方面提供幫助。
Scan concern us
